AeroSteam, Handheld Steamer, Single-Stroke Results, Quick and Easy Garment Care

• Untreated tap water:
Your appliance has been designed to use untreated tap water.
If your water is very hard, mix 50% untreated tap water and 50% distilled water.

• Types of water not to use:
Heat concentrates the elements contained in water during evaporation. The types of water listed below may contain organic waste, mineral or chemical elements that can cause spitting, brown staining or premature wear of the appliance:
- water from clothes dryers
- scented or softened water
- water from refrigerators, batteries, air conditioners
- rain water
- boiled, filtered or bottled water

In order to ensure the best performance from your iron, these types of water should not be used for ironing.

The adjustable suction allows you to choose between 3 modes: Steam (only) for delicate fabrics (silk, nylon, polyester), Steam + gentle suction for synthetic fabrics (acrylic, some cottons) and Steam + turbo suction for maximum suction and fast crease removal on thick cottons, linen or denim.

AeroSteam has been designed for vertical use without support, eliminating the need for an ironing board. As a result, horizontal use is not part of the product design and could lead to water leaks, compromising results.

Yes, the AeroSteam steamer is ideal for all garments, even the most delicate. The single-temperature heating soleplate (140°C) and the 3 modes of use make it suitable for all ironable fabrics.

The AeroSteam steamer has a fast heat-up time of just 30 seconds, which is ideal for busy mornings or for a flawless look in no time.

If the tank is empty, AeroSteam will no longer generate steam. This will not damage the appliance, but you will still be able to iron without steam. So, the ironing performance will be much less satisfactory.

It is recommended to use tap water, as the appliance's internal components are designed to work with hard water. Prolonged use of demineralised water could affect performances.

No maintenance required - no descaling needed. Our hard water endurance tests showed that over a 5-year period there was no scaling leading to a loss of performance. Based on the usage scenario: 6min/session (2 shirts) /5 days/50 weeks i.e. 125h over 5 years.

Your product is not plugged in or is not switched on ==> Check that your product is properly connected to a power socket and that the switch is on "I".
The water level in the tank is too low ==> Unplug the appliance and fill the tank.
The pump is unprimed ==>Press and hold the steam button for a few seconds to prime the pump.
The removable tank is not installed correctly ==> Check the correct positioning of the tank on the product.
The product is in "Stand-by" mode ==> Press the "On-Off" button and wait until it stops flashing.

Your product is not plugged in or is not switched on ==> Check that your product is properly connected to a power socket and that the switch is on "I".
The product is in "Stand-by" mode ==> Press the "On-Off" button and wait until it stops flashing.

The water tank is not installed correctly or its locking valve is not closed properly ==> Check that the valve is closed and that the tank is installed correctly on the product.

Your appliance has limescale, consult the "Descaling" section in the instructions.

The "Steam" button is in Continuous Steam position. Unlock it by pressing it once.

You have used descaling chemicals or additives in the water.
Never add such products to the water tank. These contain organic waste or minerals that condense under the influence of heat and cause spitting, brown dripping or premature aging of your appliance.

You have used descaling chemicals or additives in the water.
Never add such products to the water tank. These contain organic waste or minerals that condense under the influence of heat and cause spitting, brown dripping or premature aging of your appliance.

Do not use your appliance. To avoid any danger, have it replaced by an approved repair centre.

When first used, white particles may come out of the sole, but this disappears after the second use. These particles come from the product injected inside the boiler to help vaporization. You can find more information about it in the Quick Start Guide.

Take your device to a recycling center or waste disposal facility.

If you believe a part is missing, please contact our customer service center and we will help you find an appropriate solution.

Please go to the “Accessories” section of the website to easily find whatever you need for your product.

Find more detailed information in the Guarantee section of this website.

AeroSteam does not replace an iron, but complements it. In fact, their use is different: an iron is ideal for long sessions when you are ironing a pile of clothes. AeroSteam, on the other hand, is a quick solution for ironing a few items of clothing, when you are in a hurry.

Like all steamers, AeroSteam is equipped with a boiler that transforms water into steam. The big difference with AeroSteam is that it has a motor (which explains the noise) that sucks up the steam and presses the fabric against the heated soleplate. The slider button lets you choose the power of the motor, and therefore the level of suction and noise.

AeroSteam uses Calor's brand new patented Optiflow technology, which combines steam (like all our other steamers) and suction. The suction function ensures that the fabric is pressed firmly against the heated soleplate, making ironing quick, easy and effective.

AeroSteam is very easy to use:

• No complicated settings to set-up, just 3 operating modes (Steam/ Steam + gentle suction / Steam + turbo suction).
• Heats up in just 30 seconds.
• No need for an ironing board or a hook as you can simply hold your garment on a hanger.
• It has a removable 100ml water chamber (easy to fill). You can iron up to 3 shirts or 4 T-shirts in a single session.
• Your clothes are dry and ready to wear immediately after ironing, thanks to our heated soleplate technology that reduces condensation.

This is a relatively heavy iron. However, its advanced technology allows it to achieve results that are incomparable with other models. For example, instead of ironing a shirt in 5 minutes, with AeroSteam you can do it in less than 3 minutes, reducing the time you need to use the appliance.

The grid prevents larger pellets from being sucked up, while finer particles are released into the air (air flow under the product).

140°C. A resistor at the back of the soleplate transforms water from its liquid state into steam. Thanks to its direct connection to the soleplate, this resistor maintains a temperature of 140°C. This heat is ideal for ironing all types of ironable fabric, whether delicate or thick.

The triangular shape of AeroSteam reproduces the ‘precision tip’ of irons with a ‘snowplough’ effect. When the user slides AeroSteam up and down, the point of the triangle improves ironing efficiency.

Weight with cord and full tank: 1550 g

6min with full tank

No, but the water level is easily visible on the side.

Absolutely. AeroSteam is made in France at the Calor factory in Pont-Evêque (38-Isère) using strict quality criteria and exceptional know-how. It also benefits from a commitment to 15 years' repairability at the right price thanks to a network of 6,200 repairers in France, which helps to protect the environment and reduce waste.

Yes, the AeroSteam is designed to be safe and easy to use, with an automatic shut-off function that turns the appliance off after 8 minutes when not in use.

Yes, it stops if it overheats. There is a normative obligation to have thermal fuses and motor fuses. They are used to protect the appliance against sudden overloads and receiver short circuits